一本无码久本草在线_亚洲人成午夜免电影费观看_高黄高潮AV免费观看_欧美女人性体验视频_aa午夜亚洲一区二区_局长从后面握住我的奶_特一级黄色片_亚洲中文免费视频_日韩欧美高清在线观看_91在线老师啪国自产

歡迎訪問江蘇奇力泵業科技有限公司網站!
新聞中心

不銹鋼磁力泵的正確使用要領

不銹鋼磁力泵使用中環境應小于40℃、電機溫升不得超過75℃。當不銹鋼磁力泵抽吸液面高于泵軸心線時,起動前打開吸入管道閥門即可,若抽吸液面低于泵軸心線時,管道需配底閥。對于輸送液為易沉淀結晶的介質,使用后應及時清洗,排凈泵內積液。不銹鋼磁力泵被輸送的介質及其溫度應在泵材允許范圍內。工程塑料泵的使用溫度<60℃,金屬泵的使用溫度小于100℃,輸送吸入壓力不大于0.2MPa,大工作壓力1.6MPa、密度不大于1600kg/m3,粒度不大于30×10-6m2/S的不含硬顆料和纖維的液體。不銹鋼磁力泵運行500小時后,應拆軸承和端面動環的磨損情況若軸承和軸套的間隙大于0.5~1mm,葉輪軸向竄動1.5~2mm時,應更換軸承和軸向動環。因不銹鋼磁力泵軸承的冷卻和潤滑是靠被輸送的介質,所以禁止空運轉,同時避免在工作中途停電后再啟動時所造成載時空載運轉(圖\文brfr.com.cn/index.asp)。
中譯英:
Stainless steel magnetic pump in use environment should be less than 40℃, the temperature rise of the motor should not exceed 75℃. When the stainless steel magnetic pump suction the liquid level above the pump axis line, before starting to open the suction pipe valve can be, if the aspiration level below the pump axis line, pipe with valve. For conveying liquid for easy precipitation crystallization medium, should be cleaned after use, drain the fluid pump. Stainless steel magnetic pump by transmission medium and its temperature should be allowed to build in the pump range. Engineering plastic pump using temperature < 60℃, metal pump use temperature less than 100 ℃, conveying suction pressure is less than 0.2MPa, the maximum working pressure of 1.6MPa, density of not more than1600kg/m3, particle size of no greater than 30× 10-6m2/S excluding hard material and liquid fiber. Stainless steel magnetic pump running after 500 hours, remove the bearing and wear rings fixed end if the bearing and sleeve gap is greater than0.5~1mm, the impeller axial1.5~2mm, replace the bearing and the axially movable ring. Because stainless steel magnetic pump cooling and lubrication of bearings is to be delivered by the media, so the absolute prohibition of air, while avoiding work during power failure and starts caused by load carrying transfer time.